How To Change The Belt On A Shark Navigator

Shark vacuums are one of the finest on the marketplace. With their massive suction power, these cleaners come up handy on all types of floors. Add to the equation their ease of maneuverability – as most of them are equipped with swivel steering – and yous can utilize your Shark on stairs too.

Withal, despite all this, some Shark vacuums are susceptible to belt breakage.

These are the models which accept a motorized cleaning caput which relies on a belt for its rotation. What these models lack, yet, is an emergency cutoff which could close down the arrangement if the castor gets clogged. If that does happen, information technology is the belt of the Shark which becomes the victim.

Regardless of the type of Shark vacuum that you may own, this step-by-step guide volition allow yous to replace a vacuum belt without whatsoever external help.

Shark Vacuum Belt Replacement

Before nosotros lead yous through the process, at that place are some tools you need to gather. That's considering they are going to brand the entire process of removing and replacing the chugalug a whole lot easier. Brand sure you have them nearby earlier you try and supercede the chugalug.

Tools You'll Need

Screwdriver : You might need either a flat head screwdriver or a Philips one. Though as you might gauge, the blazon of Shark that yous are going to dissemble – upright vacuum or otherwise – would influence your choice
Erstwhile Hair Castor : Since you're going to open the vacuum, why non grab the opportunity to clean the brushroll every bit well? That'due south where a hairbrush volition come handy.
Scissors and Pliers: Take hold of a pair of both as they are going to help you lot gratuitous the roller brush of any objects that may have got entangled in information technology. Equally for the pliers, they will come up handy for removing stubborn objects from the roller brush.

Allow's Showtime!

Got all the higher up mentioned tools in your custody? Then let'south boot things off.

Step # 1:

First things starting time, unplug the vacuum. Follow information technology up by removing and empty the dirt canister before locking the unit of measurement in an upright position. Then lay your Shark on the floor so that yous can hands tinker with its castor roller.

Step # 2:

Best shark vacuum nv352 — remove the screws

Using a screwdriver, remove the screws which might be connecting the roller cover with the body of the vacuum. While we cannot tell y'all where to find the screws – equally each model has them on a different position – what we can clinch you lot that they'd be easy to spot.

Pace # three:

remove Shark Navigator brush roll — detach the roller comprehend

Equally presently as you'd detach the roller cover, you'd come across two ends of the roller – one which is near the belt and the other which is away from it. Grab the latter and bending information technology out of its holder.

In one case it's gratis, repeat the same procedure with the other end of the roller. If you run across that the chugalug hasn't detached yet, pull it off the roller, then skid it off the motor shaft.

Step # four:

Tools you'll need — clean the brush gyre

Using a hairbrush and a pair of scissors, clean the brush roll every bit thoroughly every bit possible. If you feel that there are some former pilus and debris that you lot can't remove hands, use pliers. Though yous need to proceed the pliers away the beard or else they might cut them, thereby doing more harm than good.

Step # 5:

Take the new belt and slip it around the motor — Take the new belt and sideslip it around the motor

Have the new belt and slip information technology around the motor, roller, and seat – in that order. Catch both ends of the roller and wiggle information technology every bit far away from the motor shaft every bit possible, while maintaining equal tension on both ends in the meantime.

Step # vi:

push the farthest end of the belt partially into the vacuum's head holder — push button the uttermost end of the belt partially into the vacuum's caput holder

In this stride, you're going to push both the ends of the belt in the holder in the vacuum head. To do this, push the farthest end of the belt partially into the vacuum's caput holder. Then, shove the nearest stop of the chugalug in its holder. When you can see that both ends are seated on their own, shove them all the manner in.

Footstep # 7:

The final step involves attaching the roller cover which you had detached in pace number i. To practise it, screw the roller comprehend into the body and gear up the vacuum upright when you lot're done. Then, test the roller by plugging the vacuum in.

Conclusion

Some people think that using a vacuum for pet hair is the biggest reason for the breaking of its belt – equally pet pilus end up clogging the brushroll. Withal, as our experts have told us, that isn't the example – as Shark vacuums for pet hair are no more than susceptible to chugalug breakage than, say, bagless vacuums from the aforementioned manufacturer.

Regardless, whatever the reason behind the breakage of your vacuum's chugalug, knowing how you can replace it on your own is going to salvage you lot a lot of stress (and money).